Insulation in Bradbury, CA
Spray foam insulation in Bradbury solves a problem most tract-home insulation crews never see: custom estate homes with vaulted great-room ceilings, stucco-over-masonry walls that were never insulated, and attic geometries that change from room to room. We run open-cell and closed-cell foam jobs here almost weekly because the foothill heat loads and Santa Ana wind infiltration demand a level of air sealing that fiberglass batts simply can’t deliver. If your Bradbury home runs hot upstairs, cooks in the afternoon sun, or sends your cooling bill past $600 in August, call (626) 341-0830 and we’ll diagnose exactly where the envelope is failing.
Why Bradbury Homes Are Different
Bradbury sits at the base of the San Gabriel range inside California’s Very High Fire Hazard Severity Zone, and that single fact changes nearly every insulation decision here. New construction and major renovations must comply with WUI Chapter 7A fire-resistive building codes, which restrict certain foam and cellulose products and require fire-rated assemblies that flatland cities like Duarte or Monrovia never have to consider. That code layer applies to walls, roof decks, and even vented attic assemblies, and it’s one reason we spec materials carefully on every Bradbury job.
Beyond code, the housing stock fights standardization. Nearly every Bradbury property is a custom estate built between the late 1950s and the 1990s, with multi-acre lots, detached garages, guest houses, equestrian outbuildings, and sprawling single-story or split-level floor plans. Attic access points vary. Wall framing depth varies. Many mid-century estates here went up with thick stucco over dense masonry or framing that never got insulated at all. Retrofitting those walls takes precision drill-and-fill blown-in work, and it’s far more labor-intensive than what tract-home crews quote. We plan for that from the first site visit.
The climate adds another layer. Bradbury’s diurnal temperature swing is sharp: summer afternoons routinely exceed 100°F while evenings cool fast, so attic insulation has to manage extreme cooling loads without letting the HVAC run nonstop. Add fierce Santa Ana winds that push through poorly sealed eaves, can lights, and top plates, and you get a home where effective R-value drops well below what the label on the batt says. Air sealing is not optional here; it’s the baseline.
Our Main Bradbury Services
Bradbury homeowners call about two things more than anything else: attic insulation that’s underperforming in the foothill heat, and crawl spaces that need encapsulation against moisture and pests. Here’s what each involves locally.
Attic Insulation in Bradbury
Most Bradbury attics we inspect are underinsulated for this climate, often holding R-19 or less in a zone that wants R-38 to R-49. On a 100°F afternoon, that gap turns the ceiling plane into a radiant heater. We start with a full attic inspection, measure what’s there, check for air leaks and rodent damage, then build the right assembly: new blown-in insulation, air sealing at top plates and penetrations, and ventilation corrections if needed. Every job is backed by the 90-Day Done Right Promise. Learn more about Attic Insulation in Bradbury.
Crawl Space Encapsulation & Vapor Barrier in Bradbury
Foothill estate homes often sit over crawl spaces that pull moisture from sloped, irrigated landscaping, and that moisture migrates into wood framing and living space. We install heavy-duty vapor barriers up the foundation walls, seal rim joists and vents where appropriate, and add drainage corrections so the crawl space stays dry year-round. It’s a one-contractor fix for damp smells, buckled hardwood, and musty air. Read the full scope on Crawl Space Encapsulation & Vapor Barrier in Bradbury.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Spray Foam Insulation in Bradbury
Spray foam insulation in Bradbury is the strongest single answer to the foothill heat and wind loads this city gets, especially on custom estates with vaulted ceilings, odd attic transitions, and rooflines that leak air in a dozen places. We install both open-cell and closed-cell foam depending on the assembly, and because Bradbury sits in the WUI Chapter 7A zone, we’re careful about foam selection and fire-rated assembly details that flatland crews rarely think about. This service almost always includes air sealing by default, which is why it outperforms batt-and-blow combinations on Bradbury’s hottest afternoons. That’s the core of what we do on this Spray Foam Insulation work.
Open-Cell Spray Foam
Signs you need it
Upstairs rooms in your Bradbury estate run 8 to 15 degrees warmer than downstairs on summer afternoons, or your HVAC short-cycles while some rooms never cool down.
What it costs in Bradbury
Open-cell spray foam in Bradbury typically runs $2.25 to $4.50 per square foot of applied area, depending on depth and access.
How we do it
We mask off the work area, apply the foam to the roof deck or attic floor at the specified depth, trim it flat, and leave the space ready for framing or storage.
Closed-Cell Spray Foam
Signs you need it
You need structural rigidity, moisture resistance, or a higher R-value per inch than open-cell delivers, often on roof decks or in WUI fire-rated assemblies.
What it costs in Bradbury
Closed-cell spray foam in Bradbury generally lands between $3.00 and $5.50 per square foot installed, with thicker lifts pushing toward the top of that range.
How we do it
We apply the foam in controlled lifts to reach the target depth, letting each lift cure before the next, then trim and inspect for full coverage at every junction.
What Spray Foam Insulation Costs in Bradbury
| Item | Typical range in Bradbury |
|---|---|
| Open-cell spray foam | $2.25 - $4.50 per sq ft |
| Closed-cell spray foam | $3.00 - $5.50 per sq ft |
| Rim joist spray foam package | $1,800 - $3,200 total |
Is spray foam safe in a Very High Fire Hazard Severity Zone like Bradbury?
Yes, when specified correctly. Closed-cell foam can be used in many WUI Chapter 7A assemblies with proper ignition barriers and fire-rated detailing; open-cell is more restricted. We verify code requirements on every Bradbury project before quoting.
Can you spray foam a Bradbury attic with rodent or moisture damage present?
No, you need the space cleaned and corrected first. We recommend attic cleaning and leak repairs before foam application, otherwise you encapsulate contamination and the problem continues behind the foam.
Blown-In Insulation in Bradbury
Blown-in insulation in Bradbury is the most practical retrofit for the city’s custom estate attics, especially where odd framing, low slopes, or cluttered access make batt installation inefficient. We use it heavily on 1950s-to-1990s custom builds where attic access is tight and the existing insulation has settled into a thin, crusty layer that’s no longer doing its job. Most Bradbury homes we test are running R-19 or worse in a climate that demands R-38 to R-49, and blown-in closes that gap fast. This is core Blown-In Insulation work, done here almost every week.
Blown-In Cellulose
Signs you need it
Your attic has settled, dust-covered insulation less than 6 inches deep, or your cooling bills spike every summer while the house still feels warm by 4 p.m.
What it costs in Bradbury
Blown-in cellulose in Bradbury runs $1.50 to $3.25 per square foot installed, with depth and attic access shaping the final number.
How we do it
We air-seal bypasses first, then blow cellulose to the target depth across the entire attic floor, checking density and coverage as we go.
Blown-In Top-Up
Signs you need it
You already have some insulation but it’s below current code depth, or an energy audit showed uneven coverage and thermal voids across your Bradbury attic.
What it costs in Bradbury
A blown-in top-up in Bradbury typically costs $1.25 to $2.75 per square foot, depending on how much additional depth is needed.
How we do it
We inspect existing insulation for moisture or contamination, then blow additional material over the top to reach R-49 across the full attic plane.
What Blown-In Insulation Costs in Bradbury
| Item | Typical range in Bradbury |
|---|---|
| Blown-in cellulose | $1.50 - $3.25 per sq ft |
| Blown-in fiberglass | $1.75 - $3.75 per sq ft |
| Blown-in top-up | $1.25 - $2.75 per sq ft |
How much blown-in insulation does a Bradbury attic need?
For this foothill climate, R-38 to R-49 is the right target, which means roughly 14 to 18 inches of blown cellulose or fiberglass. Most Bradbury attics we see are at half that depth or less.
Can blown-in insulation be added to a WUI-compliant Bradbury home without violating fire codes?
Yes, in most vented attic assemblies cellulose and fiberglass remain code-compliant. We verify the specific attic geometry and any Chapter 7A restrictions during the site inspection before we quote the job.
Radiant Barrier Installation in Bradbury
Radiant barrier installation in Bradbury attacks the single biggest heat source in the attic: radiant gain from a roof deck that can hit 150°F or more on a 100°F foothill afternoon. We staple a low-emissivity foil to the underside of the roof rafters, which reflects a large share of that heat before it ever reaches the insulation below. On Bradbury’s custom homes with vaulted great rooms and sprawling roof planes, the effect is immediate in rooms directly under the roof. This is Radiant Barrier Installation done for real heat loads, not just as an add-on.
Attic Radiant Barrier
Signs you need it
Rooms directly under the roofline stay stubbornly hot even after the AC has run for hours, or your attic temperature climbs past 130°F by mid-afternoon in summer.
What it costs in Bradbury
Attic radiant barrier in Bradbury typically runs $0.75 to $1.75 per square foot of roof area, with vaulted or complex roof planes pushing costs upward.
How we do it
We staple the foil laminate across the rafter faces, maintaining an air gap below the roof deck so the reflective surface works as designed.
Radiant Barrier & Ventilation
Signs you need it
Your attic feels stagnant and superheated, with poor airflow at the ridge or soffit vents, and you want radiant control paired with proper ventilation.
What it costs in Bradbury
Radiant barrier with ventilation upgrades in Bradbury ranges from $1,800 to $3,800 total for a typical custom-home attic, depending on roof area and vent count.
How we do it
We install or correct soffit and ridge ventilation first, then add the radiant barrier so the attic breathes and reflects heat at the same time.
What Radiant Barrier Installation Costs in Bradbury
| Item | Typical range in Bradbury |
|---|---|
| Attic radiant barrier | $0.75 - $1.75 per sq ft |
| Radiant barrier foil only | $0.40 - $0.90 per sq ft |
| Radiant barrier & ventilation package | $1,800 - $3,800 total |
Does radiant barrier work in Bradbury’s dry foothill climate?
Yes, it’s one of the most effective upgrades for this climate because it targets radiant heat, which is the dominant cooling load here. Homes with long roof exposures see the biggest temperature drops in rooms directly below the deck.
Can radiant barrier be installed in a Bradbury home with a tile or shake roof?
Yes, the barrier installs inside the attic on the rafter faces, so exterior roofing material doesn’t matter. We access the attic from below and work around existing framing, insulation, and mechanicals.
Insulation Removal & Replacement in Bradbury
Insulation removal and replacement in Bradbury becomes necessary when the existing attic material is contaminated, water-damaged, or so old it’s lost its thermal function entirely. We see it often in estates whose attics were neglected for decades, where rodents left droppings, leaks soaked through the ceiling plane, or the blown material has compressed into a thin mat. Removing and replacing also matters in WUI Chapter 7A homes where code compliance may require a different material than what was installed decades ago. See the full scope on our Insulation Removal & Replacement page.
Contaminated Insulation Removal
Signs you need it
You smell rodent or musty odors from the attic, find droppings or nesting material in the insulation, or see water stains spreading across the ceiling drywall.
What it costs in Bradbury
Contaminated insulation removal in Bradbury runs $2.00 to $4.00 per square foot, including bag-out, sanitizing, and disposal of the affected material.
How we do it
We vacuum or bag the contaminated material, sanitize the affected framing, air-seal entry points, and then install fresh insulation to the correct R-value.
Insulation Replacement
Signs you need it
Your attic insulation is flattened, crumbling, or no longer meets modern fire or energy code, especially on a Bradbury estate built before 1990.
What it costs in Bradbury
Full insulation replacement in Bradbury typically lands between $2.50 and $4.50 per square foot, depending on material choice and attic condition.
How we do it
We remove the old material completely, inspect and repair the attic floor and penetrations, then blow or spray new insulation to the target R-value.
What Insulation Removal & Replacement Costs in Bradbury
| Item | Typical range in Bradbury |
|---|---|
| Contaminated insulation removal | $2.00 - $4.00 per sq ft |
| Attic insulation removal only | $1.50 - $3.00 per sq ft |
| Insulation replacement (remove & reinstall) | $2.50 - $4.50 per sq ft |
How long does attic insulation removal take in a Bradbury home?
Most custom-estate attics take one full day for removal and another day for replacement, so two visits total. Smaller attics can sometimes be completed in a single long day if conditions allow.
Do I need to remove old insulation before adding new in Bradbury?
Only if it’s contaminated, wet, or heavily settled. Clean, dry insulation can often be topped up instead, but we inspect first and tell you honestly which path costs less long-term.
Attic Air Sealing in Bradbury
Attic air sealing in Bradbury is the step that makes insulation actually perform, and in this city it’s non-negotiable because Santa Ana winds force air through every unsealed seam in the envelope. We seal top plates, recessed can lights, duct boots, plumbing and electrical penetrations, and attic hatches with foam and caulk rated for the assembly. On a Bradbury estate with a sprawling attic, the total leakage area can equal an open window, and sealing it cuts both cooling costs and dust infiltration. Our Attic Air Sealing work is the foundation every other upgrade builds on.
Top Plate & Penetration Sealing
Signs you need it
You feel drafts in rooms below even when windows are closed, or a blower door test shows high leakage at the wall-to-attic junction on your Bradbury home.
What it costs in Bradbury
Top plate and penetration sealing in Bradbury typically runs $1,200 to $2,800 total, depending on linear footage and how many penetrations exist.
How we do it
We pull back insulation at the perimeter, apply foam or caulk along every top plate seam, and seal around plumbing vents, wiring holes, and duct chases.
Can Light & Duct Boot Sealing
Signs you need it
Recessed lights in rooms below the attic feel warm to the touch, or dusty air streams from ceiling fixtures when the AC kicks on.
What it costs in Bradbury
Can light and duct boot sealing in Bradbury ranges from $350 to $1,100 for a typical set of 8 to 14 fixtures and register boots.
How we do it
We install rated covers over non-IC can lights, seal around each fixture from the attic side, and foam or mastic every duct boot to the ceiling plane.
What Attic Air Sealing Costs in Bradbury
| Item | Typical range in Bradbury |
|---|---|
| Top plate & penetration sealing package | $1,200 - $2,800 total |
| Can light & duct boot sealing | $350 - $1,100 total |
| Attic hatch sealing | $250 - $600 total |
Is air sealing worth it before adding insulation in Bradbury?
Yes, absolutely. Sealing first prevents the new insulation from becoming a filter for leaky air, and it typically improves HVAC efficiency more than adding the same R-value without sealing.
Will attic air sealing help with Santa Ana wind dust in Bradbury?
Yes, a large share of the dust that enters during wind events comes through attic bypasses. Sealing those paths cuts dust accumulation noticeably, especially on estate homes with big attic footprints.
Wall Insulation in Bradbury
Wall insulation in Bradbury is a specialty job, because many of the city’s mid-century custom estates were built with stucco over masonry or dense framing that was never insulated. Retrofitting those walls means drilling through thick stucco from the exterior or opening interior drywall, then injecting or dense-packing insulation into cavities that vary in depth and framing style from room to room. It’s slow, precise work that tract-home crews routinely underbid because they don’t understand Bradbury’s wall assemblies until they’re on site. Our Wall Insulation crew plans for the real scope from the first visit.
Drill & Fill Wall Insulation
Signs you need it
Walls feel cold to the touch in winter or radiate heat in summer, and an infrared inspection shows empty or underfilled cavities behind the stucco.
What it costs in Bradbury
Drill-and-fill wall insulation in Bradbury runs $2.50 to $4.50 per square foot of wall area, with stucco patch and paint priced separately.
How we do it
We drill small access holes at each stud bay, dense-pack the cavity with blown insulation, then patch and texture the holes to match the existing stucco or drywall.
Injection Foam Wall Insulation
Signs you need it
Your Bradbury home has enclosed wall cavities you can’t access from the attic or crawl space, and you want a continuous air seal plus insulation in one step.
What it costs in Bradbury
Injection foam wall insulation in Bradbury typically costs $3.50 to $6.00 per square foot, reflecting the product and the precision the method requires.
How we do it
We inject slow-rise foam through small ports into each cavity, letting it expand to fill gaps and seal air paths without distorting the wall surface.
What Wall Insulation Costs in Bradbury
| Item | Typical range in Bradbury |
|---|---|
| Drill & fill wall insulation | $2.50 - $4.50 per sq ft |
| Injection foam wall insulation | $3.50 - $6.00 per sq ft |
| Exterior wall insulation (new build/reno) | $1.75 - $3.25 per sq ft |
Can you insulate walls without tearing out my Bradbury drywall?
Yes, drill-and-fill and injection foam methods both work from small access holes, usually from the exterior through stucco or from inside through discreet points we can patch and paint.
How much difference does wall insulation make on a Bradbury estate?
For stucco-over-masonry homes that were never insulated, wall retrofits often cut cooling loads by 20 to 30 percent, and rooms that used to feel like ovens in August become consistently comfortable.
Attic Cleaning & Rodent Proofing in Bradbury
Attic cleaning and rodent proofing in Bradbury matters more here than in flatter cities because the foothill surroundings bring roof rats, mice, and squirrels into attics through construction gaps and vent openings. Once they’re in, they soil insulation, chew wiring, and leave contamination that degrades both air quality and insulation performance. We remove the damaged material, sanitize the space, seal every entry point, and restore the attic to a clean, rodent-resistant condition. It’s the full Attic Cleaning & Rodent Proofing scope, done with the same care on guest houses and detached garages as on the main estate.
Rodent Proofing & Exclusion
Signs you need it
You hear scratching or thumping in the attic at dawn or dusk, find droppings near the access hatch, or see gnawed wires and shredded insulation.
What it costs in Bradbury
Rodent proofing and exclusion in Bradbury runs $800 to $2,200 total, depending on how many entry points need sealing and how much wire repair is required.
How we do it
We locate every access point from roof to foundation, seal them with metal mesh and foam rated for pest exclusion, and verify the attic is secure before we leave.
Attic Sanitizing & Decontamination
Signs you need it
Your attic smells strongly of urine or must, or you’ve had a rodent issue and the insulation is visibly stained and compressed in nesting areas.
What it costs in Bradbury
Attic sanitizing and decontamination in Bradbury typically runs $1,500 to $3,500 total, including removal of contaminated insulation and application of a hospital-grade sanitizer.
How we do it
We bag out the soiled material, HEPA-vacuum the attic floor, apply an enzyme sanitizer to affected surfaces, and install fresh insulation once the space is dry.
What Attic Cleaning & Rodent Proofing Costs in Bradbury
| Item | Typical range in Bradbury |
|---|---|
| Attic cleanout (debris & old insulation) | $1,200 - $2,800 total |
| Attic sanitizing & decontamination | $1,500 - $3,500 total |
| Rodent proofing & exclusion | $800 - $2,200 total |
How long does rodent proofing last on a Bradbury home?
A proper exclusion job with quality materials can last 10 years or more, but we recommend an annual check, especially on larger estate properties where new gaps can open seasonally.
Do I need to replace insulation after rodents have been in my Bradbury attic?
Almost always, yes. Urine and droppings contaminate the insulation and the smell persists even after the animals are gone. Replacement plus sanitizing is the only fix that restores air quality.
Home Energy Audit in Bradbury
A home energy audit in Bradbury is the diagnostic starting point that makes every other insulation decision smarter, because this city’s custom estates hide problems in wall assemblies, attic transitions, and duct runs that visual inspection alone can’t find. We test the whole envelope with a blower door, scan walls and ceilings with thermal imaging, and measure duct leakage, then hand you a ranked list of what to fix first. On a Bradbury home, the audit often reveals that the biggest energy loss isn’t the attic at all; it’s leaky ductwork or uninsulated walls behind thick stucco. That’s the full Home Energy Audit we run here.
Blower Door Test
Signs you need it
Your Bradbury home feels drafty in winter, dusty during Santa Ana events, or your HVAC runs constantly while rooms stay uneven in temperature.
What it costs in Bradbury
A blower door test in Bradbury runs $250 to $450 as a standalone service, often bundled into a full home energy audit.
How we do it
We mount a calibrated fan in an exterior door, depressurize the home, and measure total air leakage in cubic feet per minute to pinpoint the worst gaps.
Thermal Imaging Inspection
Signs you need it
Some rooms stay hot or cold no matter how you set the thermostat, or you suspect missing insulation behind finished walls and ceiling planes.
What it costs in Bradbury
Thermal imaging as part of a Bradbury home energy audit adds $150 to $350, depending on the square footage and number of scans needed.
How we do it
We scan every wall, ceiling, and floor surface with an infrared camera while the home is pressurized, documenting voids, air leaks, and moisture intrusions.
What Home Energy Audit Costs in Bradbury
| Item | Typical range in Bradbury |
|---|---|
| Full home energy audit (blower door + thermal) | $450 - $800 total |
| Standalone blower door test | $250 - $450 total |
| Duct leakage test | $150 - $300 total |
What does a home energy audit in Bradbury actually tell me?
It shows exactly where your conditioned air is escaping and where heat is entering, ranked by severity. You get a prioritized fix list, so you spend money where it moves the needle most.
Is an energy audit worth it before an insulation upgrade in Bradbury?
Yes, especially on custom estates where multiple issues compound. The audit prevents you from adding insulation to a house that’s losing more energy through ducts or walls than through the attic.
Brands We Service in Bradbury
We install and service insulation from Owens Corning, Rockwool, and Icynene, with additional options from Demilec and GreenFiber stocked for Bradbury jobs. Parts and material for common replacements are on our trucks, so most Bradbury service calls wrap in one visit. See the full list on our brands.
Pricing for Insulation in Bradbury, CA
| Service | Typical range in Bradbury |
|---|---|
| Open-cell spray foam | $2.25 - $4.50 per sq ft |
| Closed-cell spray foam | $3.00 - $5.50 per sq ft |
| Blown-in cellulose | $1.50 - $3.25 per sq ft |
| Blown-in fiberglass | $1.75 - $3.75 per sq ft |
| Attic radiant barrier | $0.75 - $1.75 per sq ft |
| Contaminated insulation removal | $2.00 - $4.00 per sq ft |
| Top plate & penetration sealing | $1,200 - $2,800 total |
| Drill & fill wall insulation | $2.50 - $4.50 per sq ft |
| Rodent proofing & exclusion | $800 - $2,200 total |
| Full home energy audit | $450 - $800 total |
Prices in Bradbury run higher than flatland cities for two reasons: WUI Chapter 7A compliance adds material and inspection steps, and custom estate homes almost always involve complex access, taller attics, and nonstandard framing that slow the work. Every quote we give is upfront and fixed; the number we agree on is the number you pay.
Neighborhoods We Serve in Bradbury
We work across Bradbury’s estate neighborhoods, from the large-lot properties along Royal Oaks Drive and Woodlyn Lane to the gated communities near the foothill edge and the equestrian parcels along Deodar Lane and Mount Olive Drive. Our typical response time in Bradbury is same-day or next-day for most calls, with emergency attic and insulation issues prioritized.
- Royal Oaks Drive area
- Woodlyn Lane estates
- Deodar Lane equestrian properties
- Mount Olive Drive foothill homes
- Gated communities near the city center
Service Area - Cities Near Bradbury
Warmline Insulation Co. serves Bradbury and works throughout the surrounding foothill and valley communities. Homeowners in Pomona, CA, La Puente, CA, Irwindale, CA, and Whittier, CA call us for the same full-spectrum insulation work, from spray foam to attic air sealing, with the same 90-Day Done Right Promise on every job.
Serving Bradbury, CA - Our Local Coverage Area
We’re based in the Bradbury area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Insulation in Bradbury
We respond same-day or next-day across Bradbury for most calls, and we prioritize emergencies like exposed wiring after rodent damage, major ceiling leaks, or failed insulation after a wind event. A live person answers 24/7 and can dispatch a Bradbury crew quickly.
Most insulation retrofit work proceeds without a separate city permit, but Bradbury’s WUI Chapter 7A designation means certain spray foam and structural changes need fire-rating verification. We check the specific scope against current codes before quoting and pull any needed paperwork.
Yes, we work on detached garages, guest houses, equestrian outbuildings, and secondary structures across Bradbury. Each gets the same inspection, scope, materials, and 90-Day Done Right Promise as the main house.
If your Bradbury home is fighting the foothill heat, leaking air during Santa Ana winds, or running up cooling bills that don’t match the square footage, call (626) 341-0830 for a free estimate. We’ll diagnose the actual problem, quote a fixed price, and most jobs wrap in a single visit. A live person answers every call, 24 hours a day.
What happens when you call
- 1A real person answersNo phone trees - talk to a local insulation pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3A background-checked tech heads outLicensed & insured, typically same-day.
- 4You approve before work beginsNothing starts until you say go.
What Bradbury Customers Say
"Rodents had been in the attic for years before we bought the place. They vacuumed everything out, sanitized, sealed the entry points with mesh and foam, and only then put new insulation down. Photos of every stage before I paid."
- Darnell Whitfield"Crawl space smelled musty and the floors were cold. Full encapsulation with the thick liner taped at every seam, and a dehumidifier sized for the space. The hygrometer they left reads 48 percent now instead of the 70s."
- Elena Vasquez"Upstairs was ten degrees hotter than downstairs every summer. They pulled the attic to bare joists, air-sealed every can light and top plate first, then blew it to R-49. First August in this house where the bedrooms and the living room read the same on the thermostat."
- Marcus Hale